Fixed Brake Line - Family Fish - Big Storm Coming!

As soon as the auto parts store opened up this morning, Steveio was there at the door, ready to get the proper brake line fitting for motorhome. He also grabbed 3 quarts of synthetic Dot 3 brake fluid with a high boiling point as well.  He is not sure how much fluid leaked out, so he is best to be prepared with enough plus some for bleeding the brakes afterwards.

Before I could start on my second cup of coffee, he had put on his overalls and crawled back underneath the motorhome. I only had to hand him a few things because he already knew what he was doing with his various flaring tools, tube cutters, and wrenches.

Here is a section of the rusted out brake line that he removed, as well as now putting a new fitting on the end of it.

What a grubby looking thing, eh? That's what a combination of age (22 year old motorhome) and Wisconsin Winter Roads With Salt do to the undersides of our vehicles.  Remember, just a few weeks ago we also replaced the rusted out muffler.

Once he was assured that all of the brake lines were good, he took out his air pressure brake bleeding tool. He got that a number of years back from Harbor Freight.  Here is a link:

Pneumatic Brake Fluid Bleeder with Auto-Refill Kit

It has proved invaluable for drawing through the new brake fluid through the long runs of brake lines on a motorhome.  It operates with the air compressor and pulls the new fluid through the lines while sucking out the old stuff into the white chamber.

Steve keeps his air compressor in the motorhome. It is able to handle all of his air tools and stows compactly away in a basement storage compartment until we need it.  I bought it for him years ago for Christmas and it's just the right size. He has a different one now in the garage, so this one can stay in the motorhome all of the time.

He fills the main reservoir of the brake system up to the top with the new fluid. Then he uses this device on each of the bleeders at each wheel. It draws through the new fluid and at the same time removes the old fluid. Of course, in this case we don't have any old fluid because it all leaked out!!

By using this bleeding tool, it also suctions out all of the air in the lines so we never have a bubble. That can be dangerous. He used up one full quart and 3/4 of another bottle of fluid to adequately purge the system of air and make sure each of the brakes has fluid right up to the bleeder.

He had it all done before I could snap a pic underneath.
This is all I got.

Once he was done with that, he went inside and started up the motorhome. He pumped the brakes a few times to feel the pedal return to its normal position. Of course, since we are set up for a week on the campsite, we won't be taking it out for a test drive until we are ready to leave.

But he is confident that we are now "Good To Go"!

~~~~~~~~~~

I spent the rest of the morning working on a project myself. It's a "Repurpose Recycle Reuse" project!  And it has to do with fish???

If you've read my blog during the last few weeks you know that we built a bunch of cute shutters to dress up the exterior of our home. The motif we chose matches the fretwork cutout design of the lattice below our front porch.

The shutters sure came out cute 

and we are happy we did that....

Okayyyyyy 

now you may be asking yourself, 

what do shutters have to do with fish? 

Or recycling for that matter?

How could you toss these into a scrap pile? Steve was even going to toss them in our backyard campfire. No way. I could see a fun game coming out of these.

Well, just look at those cutouts. Tell me what you see? I saw it. I had an idea. I asked Steve to cut each of the pieces in half, at the center most point.

I tossed them in my handy-dandy weeding bucket from my brother-in-law Pete. I'm done weeding my garden, so right now this bucket can be for the fishing game, okay Pete?

I brought along my electric pad sander, my glue gun and a pack of magnets. Oh boy, when I get creative there's no stopping me.

I sat outside of the motorhome and sanded off all of the rough edges around each fish. There weren't any other campers nearby us, so I wasn't bothering anybody.  Steve said he thought I looked so cute and snapped this pic of me. Awwwwwww

I sanded down each fish and got myself covered in sawdust at the same time. What fun!  I love fun projects and using power tools.  The smell of fresh cut wood reminds me of the fun time we had building our log house together after we first got married.  Ahhh memories.  Anyhow, back to the fish---   I was having fun and not making too much of a mess.

My next step was to grab my wide permanent markers. I wrote each family member's name on a fish. I also included all of their dogs and cats as well.  I added all of the kids, grandkids, great grandparents and the nephew, wife and two cousins who are also coming on Saturday to the park.   I had to make a list to not forget anyone.

Using my hot glue gun, I attached strong magnets to the mouth of each fish. Whatever did we do before the age of glue guns?  I am using the new Gorilla Glue sticks, that really seem to hold better than the older style sticks.  I glued the magnets at bit of an angle to fit the drilled out hole of the shape.  (Steve had to drill pilot holes on each end of the pattern to get the jig saw blade started to make the cutout).

I have a long bamboo fishing pole I found in our garage attic from the previous sellers.  Steve will cut it in half for me tomorrow and sand the edges. I am adding strong cords and two round magnets to the ends of the cords. That way the kids can "fish" by hooking onto the magnets, either from the bucket or from behind a curtain or a panel so they can catch random fish and be surprised by who they catch! 

I started lining them up to cool off the glue 

while the dogs watched me work.

Lining them up was fun,

and I started sorting them out and 

grouping them by family.

This was fun! 

After each one cooled, I lined them all up on the picnic table.  There are 33 in all completed, and I have more unpainted ones to add to the group later.  I might add my own siblings and their grandkids too. 

I can just see our grandkids 

making up games 

and rules for the games, 

and learning to identify family members, 

reading the names, 

teaching the younger kids, 

and 

catching various fish 

from a hidden space behind a blanket 

or out of the bucket? 

We will call it:

"FAMILY FISH"

~~~~~~~~~

This afternoon we got warnings on our phone of bad weather coming across Wisconsin.  The radar didn't look too good.  Since we had a lot of rain the last two days, the ground at the park is totally saturated.  High winds combined with the shallow root systems in the park (due to being on the Niagara Escarpment of rock cliffs)  Trees are known to blow down easily, and we kinda sorta know what to expect. 

SEVERE THUNDERSTORMS WITH DAMAGING WINDS AND TORNADOES POSSIBLE DURING THE AFTERNOON AND EARLY EVENING... THE POTENTIAL EXISTS FOR SEVERE THUNDERSTORMS ACROSS THE AREA DURING THE AFTERNOON AND EARLY EVENING HOURS. THE STORMS ARE LIKELY TO PRODUCE DAMAGING WIND GUSTS. LARGE HAIL AND TORRENTIAL RAINFALL IS ALSO POSSIBLE. 

SEVERE THUNDERSTORMS POSSIBLE THROUGH THE EVENING... STRONG THUNDERSTORMS WITH HEAVY RAINFALL, GUSTY WINDS AND HAIL WILL CONTINUE ACROSS NORTHERN WISCONSIN THROUGH EARLY EVENING. THESE STORMS MAY BECOME SEVERE AS THEY MOVE RAPIDLY THROUGH CENTRAL AND EASTERN WISCONSIN BETWEEN 8 PM AND 11 PM. DAMAGING WINDS WILL BE THE PRIMARY THREAT, BUT ISOLATED TORNADOES AND LARGE HAIL WILL ALSO BE POSSIBLE. 


We made a wise decision to head into town to our house. It's only 15 miles away, so we figured we would hunker down at our house, and leave the motorhome at the park. We rolled up the awning and put away our lawn chairs.  There aren't too many people camping this week, so we are not really needed to be there. We notified the rangers and the park superintendent that we were leaving for the evening.  We popped the dogs in the Tracker and headed back to town.

Things are looking grim, and the winds are kicking up.  We went for a quick walk around the block with the dogs, and almost got blown away down the street.  A few sprinkles were starting as we made our way back to the house, safe and sound.

The rolling and boiling clouds 

look eerie against the night sky

and the church tower. 

Since most of our "cookable" food is out in the motorhome's refrigerator, we decided to order Chinese take-out here in Chilton. We don't often do that. Steve had Spicy Beef and I had Shrimp with vegetables.  The dogs got the fortune cookies!  

Tonight we will sit here and watch some movies, check the weather reports and be safe and sound in our house. I hope all of the storms blow over, and are not as ominous as some of the weather reporters are making it sound.  I just shudder to think of the blowing winds and toppling trees in the park. Our motorhome is insured, but our lives are not. Better to be safe than sorry!


.

MOTORHOME MODIFICATIONS *B* Brake Fluid, Brake Pads and Brake Lines and My Quilt Top

I am going to start off the new year with posting three of our motorhome modifications at a time. I will post repairs, modifications, or neato things we have found for RVing.  I have lots of pics in my files so I will do them in alphabetical order.

Underneath that stuff, I will post my regular daily stuff..... kinda sorta fun, eh?

So here it goes:

MOTORHOME MODIFICATIONS 

STARTING WITH THE LETTER B 

Brake Line Fluid:

I think we can all agree that brakes are a pretty important thing on a huge 30,000 pound vehicle!

Motorhome brake fluid should be changed yearly, or at least every two years, for safety.  Because of the long length of brake lines in motorhomes, with more connectors and fittings than in a car, there is more chance of intrusion of moisture.  And, of course, moisture means brake failure if it reaches a boiling temp in much-needed braking situations.   When draining out the old fluid, it's very brown and root-beerish looking, and you can easily see that it needs to be replaced completely with fresh fluid. Not just added at the reservoir, but pulled completely through the lines.

We do it right in our own backyard....

Steveio has this nifty tool from Harbor Freight that utilizes an air compressor to remove the old brake fluid from the motorhome lines and at the same time, draw in the new fluid so there are not any air bubbles.   This tool runs about $20.  We use 2-3 of the big jugs of DOT 3 brake fluid.

It means getting down on the ground and doing some grunting, but it is worth it to do the job yourself so you know it is done RIGHT.... (and save money)

My job is to pour in the new fluid as the level was sucked down through the lines.  Normally you can use the second device in the box to let the new fluid come into the reservoir on it's own, but we don't have much clearance under our Safari to do that.  So it's easier to just have a second person to pour it in while Steve uses the tool to draw it through the lines.

Starting at the back tires, each line gets refreshed with new fluid.  Then we double check that all the lines are bled and I push the brake pedal down inside while Steve does the bleeding.  I push hard down on the brake pedal while he turns the little bleeder fitting until clear fluid comes out in a nice stream without bubbles or erratic squirts. It takes a little while--- with him hollering from underneath while I try to hear him over the buzzer warning alarm inside that happens when the brakes are depressed when the engine is off.  But we get it done and save a lot of money---- plus we are sure it's done RIGHT!

Brake Pad Replacement (while on the road):

We were on vacation out in western Texas in 2013 we realized we needed to do a brake pad replacement on the front wheels.  We were camping near Del Rio, a tiny dusty border town. We called a Napa auto parts in that town and ordered the pads which were to arrive the next day. 

NAPA number UP 7149-M  $130

Steve got some of the lug nuts loose while at the campsite, but decided to drive the whole motorhome into Del Rio to a tire place to get the rest loosened. They kindly offered their empty back lot to park in for us to do the work!  The nice guy named Travistino (sp?) came around back with his service truck and loosened up the last few lug nuts for us.  Look at this Big Boy Tool!

 The charge???  $5.00.... yes.... $5.00!  

 (I gave him a $10 tip and said to buy lunch)

Then we went to work.  First we had to jack up the motorhome on the front leveling jack till the tires cleared the ground.  We stacked up heavy wooden planks under the axle in case the front jack gave way.  Never hurts to be safe.  Then Steve was able to remove the driver's side tire and get to the brake system.

He removed the top retaining plate which the bolts came out easy enough. Then he was able to remove the tensioner spring.

He tapped lightly on the "keeper" pins?  Not sure what they are really called, but that is what Steve calls them.  He used a hammer and a tip of a chisel to lightly tap them loose and slide free.

Next he used a very large C clamp to compress the caliper cups and was sure to open the top of the brake fluid reservoir to let out any excess fluid from compression.

Steve said to note in the picture on the left, his reinforced top of the shock absorber mount that he repaired after it broke.  He super duper welded it and made it even better than before. Steve noticed in New Orleans on Eric's rig, his has been repaired too.  So it must be a common problem on Safari's with the Velvet Ride? Also we have since changed the shocks back to Koni brand for a better ride. I will do a blog post later when I get to the letter *S* for that. 

Back to the brake job-----  Now he could take out the pads from the caliper.  They almost fell out into his hands.  The caliper itself looks good, but needs some rust removal along a few edges.

OH MY GOD----- LOOK AT THESE!

Guess we needed new brake pads, eh?

The rotors appeared to be in very good shape, so we were lucky to do this pad replacement job now, and not later when they would have become more worn and damaged the rotors.

Once he got the brake pads out, he took them with him.  He hopped in the Tracker and went over to NAPA on the north side of Del Rio where our new ones had come in on the truck an hour before.  Amazing--- we ordered them at 4pm and they were on a truck ready for us to be picked up by 8am the next morning.  What good service!

Here is the box with the part number that NAPA used after cross referencing the numbers we got from other Safari owners.   Steve was told the pads are actually the ones made by Bendix for the Ford Truck braking systems.  That is good to know too.

Steve matched them up at the store, and they were a perfect fit!   They cost $130 for both front wheels, and he also bought a bottle of Copper Never Seize for $10.   Soon he was back at the motorhome and ready to get to work.

Out came the rest of his tools and he set to work.  It was fairly warm in the low 70's so his brown overalls were needed for protection while he worked, but soon got hot in the sunshine.

Before reassembling any of the brake parts, he used the generator to power up his grinding tool.  The wire cup brush took off any excess rust and cleaned up all the parts nicely.

I was the gopher and the wheel turner and the tool hander and the picture taker! 

Then he dabbed the brush of Copper Never Sieze on each piece that needed it, including the keeper pins (if that is their name?)

When assembling the caliper unit back together, you have to be sure to get these two metal discs in the right place inside of the cups before setting the pad into place.  You need three or even four hands to do this, especially if you keep the brake line attached like Steve did.

He gently tapped the keeper pins back into place and also coated the saddle groove they rest in with the Copper Never Seize too.  Once the whole caliper assembly was together, he was able to slide it back on over the rotor disk and bolt it all into place.  He even put the Copper Never Seize on the bolts that held that retaining bracket in place too.

Now.... he did the same thing to the passenger side as the driver's side... both front brakes were serviced.  What a job!  In a parking lot in a desert city with all his tools on board. What a guy!   See why I keep him around?

It was time to put the tires back on, and lower the jack a bit till the tires were snug to the ground.

Bit by bit, he tightened up the lug nuts with the torque ratchet to 170 ft pound as high as it will go.  After we drove it around to the front, the nice guy Travistino tightened them up to spec 500 ft pounds with his torque bar on air ratchet.   Steve estimates it was about a two hour job to do both front brakes. We saved a LOT of money by doing it ourselves.

We stopped into the office of the tire place and thanked them for the use of their back parkinglot to do our brake job. They smiled and said no problem. I talked with the owner a bit, a nice woman, and gave her $30 to order some pizzas or donuts or something for the three guys who work there. With a nice wave from Travistino, we were on our way!

Later on that summer, we did the two rear brake pads in our own back yard, they were close to the same price and are same exact pads as the front brakes.  We ordered them from our local Napa dealer and got them in one day.
$140.70   Napa part number UP-7149-M

Brake Line Failure and Replacement:

Not only do brake pads and brake fluid need replacing, but the lines that carry the fluid to the brakes sometimes need replacing too!  

On another trip, this time to New Mexico in February of 2015... Steve noticed a big oily spot under our rig just after we leveled off in our campsite.  Rut Roh!  Breakdown again!   

I am soooo thankful that Steve notices all of these little things before they become big or dangerous disasters.  He is always watchful and keeps on his toes in regard to maintenance of our motorhome. 

The brake line seems to have broken leading up to a front wheel.  Good thing we were near a large enough town to get parts.  Steve blamed me for "breaking the brake" because I was the one driving the motorhome up on blocks to level it. He said I stomped on the brake pedal too hard!  Well, better that it breaks here in a park rather than in the middle of some mountain descent, right????

Now it was time for Steveio to get to work!  He got down and dirty to figure out the busted brake line, and take measurements and get a good idea of what parts he would need to fabricate a new line. 

With all of his notes in hand, we trooped on into town.  He dropped me at Walmart for a grocery stock up session, while he hit the autoparts store with his list of items.  Sadly. they didn't have what he needed!

Now here it where it turns into the GOOD NEWS!!!

Another customer, standing in line behind him says: "Hey, I own a truck repair shop down the highway and I can custom make that brake line for you. Just bring the old one on over and we can set you up!"  Wowzer!!!! After some discussion, he said it would be better if we could drive the rig right over to his shop, and he can examine it firsthand before fabricating the new line. He even offered to let us stay in his lot overnight if we got over there too late in the day to get started on the job!

Amazing!

What are the odds that Steve would be standing next to one of the only truck repair places in 50 miles around who can custom make brake lines and has all the lines, fittings and tools to bend them???

Yes, the Motorhome Gods were smiling down on us!

We rushed back to the campground and Steve donned his overalls.  (yes, he takes them along on the road just in case!)   He was able to temporarily patch in a piece of line with some compression fittings to get us limped down the highway 25 miles to the truck place.  We also have our Pac Brake engine exhaust brake to help stop us, but it is best to patch this line in the meantime and we have brakes enough to get down there.  So here is my Mr. FixIt Guy laying on an old Thanksgiving table cloth as he works on patching the line.

He was done with the temporary patch job, and out he bled the lines while I pumped from inside. Everything held and we were good to go.

On a positive note, we arrived safe and sound at Harold's truck repair place.  It is called Emergency Truck Repair right off the highway at Caballo Lake, NM.  It's comforting to see that he is working on all the local folks vehicles, the county ambulance, and even the Derry Arrey Fire and Rescue vehicle.  If the locals trust him with their things, we should be in for a good experience.

Harold came out and checked the line on our rig, and yes, he said that he can easily make that line.  Steve suggested that perhaps he should make up another front brake line for the other side as well, so now we will be good to go if Harold can make both of these for us.

The only problem is Harold can't do the labor himself to install them, because he had recently hurt his shoulder really bad... Harold thinks he tore his rotator cuff.  His doc appt was the next afternoon.  So he said to Steve: "If I make the parts in the morning, can you do your own labor??"   YESSSS !!!!  That will save us in labor costs, and Steve is more than adequate at handling the installation of the new lines.  We even have along our power bleeding tool device that runs off our air compressor. Whew.... that is a good thing!  Silver Lining, perhaps?

See, the problem is that the brake lines are a flexible type, 36 inches long, and need to be specially fabricated for a long-defunct chassis company on our 22 year old motorhome!   (Magnum chassis manufactured by Safari when it was out in Oregon)  And he did it!  Great guy!!!!   

Here is a pic of the extra one for the passenger side:

We had a safe night sleeping in our rig in his gated shop yard. Steve got the new brake line fabricated from Harold in the morning, and Steve set to removing the old rusted fittings from the old line and installing the new line in it's place. 

In the meantime, Harold had to lock up shop and leave for a doc appt.  We were out in the parking lot working on it with our front end up on blocks and the front hydraulic leveler for added stability. Steve used all his own tools too, so Harold could lock up his shop and go.   

So once we were done testing the new line, we didn't know how much to pay.. or WHO to pay because there wasn't anyone around!   

Harold thought he would only be gone 1 or 2 hours. He said that when he came back he would make up a duplicate line for our passenger side for Steve to change out later on.  It was 5:30 before Harold got back to the shop. 

He made up the duplicate line and we were good to go for under $100.00  WHEEEEEE  Thank you Motorhome Gods for putting Steve in the right spot --- at the right time --- to meet with the right guy --- who can make up these special brake lines for us!!!!

~~~~~~~~

Steve was gone most of the day yesterday for work.  I am still hanging out at home, being a recluse and healing from the pneumonia. I would say I am feeling 80% better, but still weak and tire easily. I am very very afraid of picking up a flu bug or other virus out there, so I am staying home inside. Safe and sound.

I did finish sewing together all of my blocks for my Twin Turtle Coffee Quilt. The quilt is named after the shop that I won the fabric from in October for a contest. http://www.twinturtlequilts.com/

Here is the finished quilt top (not yet quilted or binding edges) on our king sized bed. It hangs down on each side about 8 inches, so I want to add a border to make it a bit wider, as well as taller at the top to make a "pillow tuck" area.

I like the three dimensional look to the blocks, 

with the darks and golds to the upper rights

and the creams and beiges to the lower lefts.

I think for the border I will do a strip of cream and then a strip of this adorable coffee bean fabric. I made up four border variations in photos and posted them to my quilting group. I asked for their opinions on which way to make it, and most of them voted for this number 3. 

This is the coffee bean fabric I am using for the border and also the entire back of the quilt!  I saw it a while back at Joanns Fabrics, but when my friend Vicky and I went there for a shopping sale, we could not find it again. I looked online on my phone and it said that store should have about 8 yards of it in their inventory.  So we looked and looked again. I was ready to give up, but Vicky found the bolt of coffee beans setting behind the cutting table in a big bin of fabric!!!! Thanks Vicky!  Moral of the story, "Never Give Up"!

And.... I got to use my coupon for a discount on the fabric!  

The weatherman says we are due for our THIRD January Thaw this weekend!!!  I am looking forward to some warm sunshine and perhaps coffee out on the front porch.

Keep tuned to my blog, we are going to replace the king sized mattress in our motorhome with a new memory foam one if the weather cooperates!  (we want dry pavement to use our little flat trailer to haul the mattress home).  So we will see if Steve and I can wrestle the old one out and get the new one in?  Either that, or Steve will call on a buddy to come over and help.