Now what is my guy doing bending over by the toilet? He's not sick!
He is actually removing some of the old quarter round trim around the toilet in preparation for the next project.
He decided that he looked at the pile of beadboard slats piled up out in the garage long enough. It was time to get them cut to size, brought in the house, and installed on the last two walls in our bathroom.
This little area around the toilet with the three walls and the two little edges around the corners needs to get completed with the beadboard.
The other wall underneath the window and the area around the sink still needed to be completed. That's one of the most complicated walls with the most technical cuts.
Last year we had completed the wall along side of the bathtub and around the corner to the master bedroom. We also completed the other wall near the linen closet and alongside of the end table with the stained glass lamp. Those were the two widest expanses that needed to be done. They were easy because it was one piece after another - boom boom boom - dune.
Steve started working on the odd cuts to get around the lip edges of the sill and then he fortunately was able to just loosen the brackets on the pedestal sink and work in the boards behind it. That was much better than having to dismantle the whole sink.
This wood is comprised of thin pine slats that have a tongue on one side and a groove on the other. The front portion has two sections of beadboard, about 3 1/2 in wide. Here is a profile end shot of a slat.
It can be applied with small finishing nails while making sure each tongue is snugly pushed into each groove. Steve has also opted to put a layer of special adhesive on the wall behind each slat to make sure that they are securely fastened. Otherwise they may be subject to warping and shrinkage over time. So we fasten them both ways to be extra secure.
On Saturday morning, it was time for me to get out my paintbrush and start getting the first coat on the beadboard. The temperature is here in Wisconsin have dipped way down, below normal, which is pretty much like the rest of the country it appears to be this week. Good to do some inside projects today.
We were babysitting one of the granddaughters, so I bravely wrapped her in a an old t-shirt and put her to work. She has helped me before and even though she's only 6 years old, she does a very good job.
She loves the little roller. It's just her size. It works out really well to have a tiny person assisting. She could easily fit between the bathtub and the window to work on the wall underneath.
I could also stick her underneath the sink to roll that portion of the beadboard. Because the baseboard is already the same color as well as the window trim, we really didn't have to worry about her bumping anything other than the shower or the sink. Those were easily wiped off of any "oopsies".
We also gave her the opportunity to learn about "Lefty Loosey and Righty Tighty". She was able to take off the two screws that held the heating register grid in place. They are never too young to learn.
One good coat of paint, and then it was time to clean up, curl up and take a little nap together.
After nap time, she was ready and raring to go to put her painting clothes back on and get back to doing a good job.
Soon we had two coats on everything on that wall... while Steve was working on the other area over by the toilet.
Fortunately, the toilet is almost 4 inches away from the back wall. It was good that we placed it far enough away when we changed the flooring. Now Steve had room to get in behind there with the boards without having to maneuver around a tightly fitting tank. Plus, I can get back in there with the roller to paint the beadboard once it's in place.
He was able to work into the tight corners with his battery powered finish nail gun. Sitting backwards on the closed toilet seat really made it easier to work in such close quarters. It looks funny, but it makes a good work surface to lean on when working on the back beadboards.
I was able to get the first coat of paint on this next part of the beadboards, and Steve started cutting the top cap trim wood. It has a little bead roping and also some egg and dart design like the original trim around the windows on our 100+ year old farmhouse.
That was enough for Saturday. It was time now to take it easy for the evening, pop some popcorn and watch a movie with the granddaughter. We got enough done for one day. So we popped our ibuprofen and went to bed early.
Sunday morning we were able to finish up the rest of the trim and I gave everything a quick second coat of paint. It really came out nice. We just have two little pieces of cap trim to put on each side of the mirror and two L-shaped corner pieces on the edges around the toilet space. We have to stop up at the Home Improvement store to pick up a couple pieces of the L-shaped trim. Then we are done!
I'm quite pleased to have this finished up. I was thinking it was a midwinter project. I'm glad that Steve decided to get it done now and get the wood out of the way from in the garage. He's been reorganizing out there and this wood has been setting in his way since last winter.
~~~~~~~~~~~
Here is my little Sullivan table craft table that I picked up at the thrift store last week for only $10! Works out very well also as an ironing surface.
I am prepping this quilt top to get ready to roll it onto my big frame. I lay down my big board ironing board across the entire length of the craft table. Now I am able to iron portions of the quilt without the rest of it rumpling up or landing on the floor.
What's great about a rectangular shaped ironing surface for a quilter is that you're not dealing with the funny angled nose edge of a traditionally shaped ironing board. Seeing as most quilts are straight lined shapes, it makes sense to get a larger surface for ironing on with a rectangle shape.
~~~~~~~~~~~
Growing up in Upper Peninsula of Michigan, some local foods are imbedded deep in my heart. In the tiny town of Caspian, Michigan, almost every kitchen had this iconic red lettered brown paper bag sitting near their breadbox or next to the coffee pot.
My daughter brought me a bag today as a gift, and babysitting thank you.
From their website:
Our original and most popular flavor of Trenary Toast - made in Trenary since 1928!
This crunchy snack is coated in our signature blend of cinnamon and sugar, and is ready to be dunked in your morning coffee, afternoon tea, or late night hot cocoa.
For over 90 years Trenary Home Bakery has specialized in the production of this Finnish Korppu - try it today and experience Michigan's favorite breakfast treat!
We sure are taking our hibernation seriously in January. We really have been snuggled in and not doing much. Sorry, I let this blog slide for three whole weeks before I realized I haven't posted!
In the middle of the month on the 17th I held a meeting of our Home and Community Education group here at our home. It's a County Extension group commonly called The Homemakers. Steve calls it The Homewreckers! LOL Our membership numbers are down due to some people not feeling well, and doing social distancing to prevent the spread of covid. A few of them have traveled to the South as snowbirds, and one of our members happened to break a leg and now is at a rehabilitation center!
For the six who had made it here to our home, we had a delicous potluck meal and I had set up the dining table for our meeting after our dinner. It was a nice social event afterwards and it was really good to see some people again. Steve escaped to his brother's house down in Menasha for the day. Everybody is fully vaccinated and boosted, and practicing as much social distancing as possible. Hopefully, the numbers are falling now in Wisconsin and we can start doing things again. I had still kept all of the Christmas decorations up both inside and outside to have the house look it's best during our meeting. (plus it had been too danged cold outside to take them down yet).
The next day after the meeting, Steve said it was time to start taking things down. We came up with a different idea this year for our 9 ft tall artificial tree. Instead of taking it apart into five individual pieces, which take up a lot of room on the shelves in the garage, we came up with a different idea. Someone else had mentioned doing this and I looked it up on YouTube. A lot of people have tried different techniques to do this, but we came up with a few of our own.
First we wrapped from the base of the tree stand up around the top and back down the base again in quadrants around the tree. About 10 good strands of this plastic rolled shrink wrap. It took two of us to get around the base and through the openings and back up again over the top.
It also took two people to do the next part. One to hold the tree and keep it from rotating while the other one used the wider roll of pallet shrink wrap to go around the tree. Around and around and around we went. Working as a pair to get the tree completely wrapped. The tree still has all of the ornaments and lights and ribbons all in place. We did remove a few precious glass ornaments, but the rest of them are wrapped right into the branches of the tree.
We squashed it as tight as we could around the bottom to get it narrow enough to fit through our 36 inch wide door. It was a squeeze, but we managed to get it out. By wrapping it from top to bottom first, that secured the tree to keep the center trunk pieces from coming apart as we brought it out to the garage. Once we got it into the garage, we stood it up right again and tucked it back into the corner. Hopefully it will stay nice over the rest of the winter and throughout the summer months. Next December we can carry it back in and carefully snip away the plastic with a scissors and be careful not cut into any of the wires or ornaments. A little fluffing to the branches and rearranging a bit and I think it will be just fine! Sure beats having to undecorate it all, take off the lights, then store everything away in totes.... Then take the tree apart in sections, wrap them all up in huge contractor garbage bags and stack them out on the shelf. The added plus is now there's more room on the shelves to put some of my other totes and organize the garage a little better! It's kind of the "overflow storage" for a lot of my weaving fabric and supplies.
(notice Steve's insulated ceiling in the garage!)
We had one warm day before the weather turned blastedly cold. It was about 35 degrees so we were able to get out and get the decorations off the front of the house. It was warm enough we really didn't even need to wear gloves so we could snip all of the ties that held everything into place.
Our son-in-law, Jesse, does a lot of 3D printing. The raw material he uses comes on these big plastic spools. He saved us a bunch of them so we could wrap up our red velvet ribbons to save again. That is a lot better than just throwing it away and buying new stuff next year?
We carefully unwrapped all of the ribbon from the pillars and removed all of the lit garland from the railings. Everything is carefully layered in big boxes. The big snowflakes came down and were packed in a large flat box. The house looks so plain now!
The plastic spools even worked good to take off the outside lights that we had on the pergola and tiny tree. What a nice way to store them and they are tangle-free.
Now all of the decorations are stowed away and it's time to look ahead for the rest of the upcoming winter. The holidays are over and the dreary winter weather is going to set in. We have considered maybe going away to the desert for the rest of winter, but instead we are going to hang closer to home. I think we are going to plan on a trip this summer across the United States may be heading out west on US 2 and go all of the way to Washington State. In the meantime, we will hunker down and work on some winter projects.
~~~~~~~~~~
I am pleased to say that our removal of our electric water heater and our Christmas Present installation of our tankless natural gas water heater resulted in a $30 decrease in our electric bill last month! That is almost 33% of our entire monthly electric killowatt usage! We will get an even better figure on our savings by the next bill without the added Christmas lights on it. We didn't see much difference in the natural gas therms usage from last years bill, but we will compare them again on the next bill.
~~~~~~~~
The pineapple quilt that I was working on is finally fully assembled. I got it rolled up onto my big quilting frame with the backing and the batting in place. I wanted to pick up some variegated purple / pink / blue thread for the quilt so I'm waiting to get started until the new thread comes. This is a queen size that will be for sale in my Etsy shop soon.
I really try to discipline myself that I won't start another quilt until I finish the one I'm currently working on. It keeps me from getting too many projects going at the same time. Because I wasn't going to get the thread right away, I did start on the next quilt. Shame on me!
If you've been reading my blog for a while you know that all around my house I have stained glass light fixtures. Most of them are from the same line called Belle from Menards. I have 2 bedroom ceiling fixtures, a 5 shade chandelier in the kitchen, 3 wall sconces in the She Shed, 2 reading pole lamps and 3 table lamps in the bedroom and livingroom. They are throughout the house and I really enjoy them. I even have one hanging down as a pendant over my kitchen sink.
they are all like this:
I had decided that I needed to make a quilt to match the light fixtures in the bedroom. Last summer after we installed the large window, the beautiful blue and white quilt on our king size bed looks out of place. So I decided to go through my stash of fabrics and pick out everything that was coordinating colors with this stained glass. I did have to make a run to a little quilt shop up in Marinette to pick out a few more coordinating fabrics. Other matching fabrics I had picked up last fall on our trip out to the Mississippi River along the western edge of Wisconsin. I had this quilt in mind, so I had set those fabrics aside as well. Now I had enough to begin. It's a very simple pattern, only utilizing these two blocks. It's how you put them together in a big array that makes the difference of the quilt!
I started cutting out squares, carefully measuring and arranging my supplies. I like to have everything pretty much arranged at my fingertips while I start creating. I'd rather have it all there then fly by the seat of my pants and run too short later. That way, if there's extra fabric I can always make some into throw pillows to put on the bed after the king size quilt is completed.
I got about 60 blocks sewn already. The littlest granddaughter Claire was over the other day, and she helped me arrange a few on the floor to get an idea of how it is going to work out. Of course, Binney had to oversee the whole process.
I won't start sewing them into strips until I get them all laid out. I am trying hard to not let any two of the same colors touch at any of the seams. So once I get it all laid out, I will carefully number each one by row and column before sewing them together.
It will eventually end up looking like this... but king sized with a lot more blocks. Some nice borders and trim will round it off. I think I am going to like it. Then my sister wants my blue one for her king sized bed!
~~~~~~~~
The weather has been terribly cold, well below zero with awful wind chills. Claire's parents were going up to their cabin for the weekend, but they asked if she could kind of hang out here and stay warm with us. There would be no outside fun playing in the snow for her when the wind chills were twenty and thirty below zero!
It was nice and cozy warm in the She Shed and she was helping me weave on the big Sanna Kangas Finlander Barn Loom. She sets her little butt on the bench right next to me, just like many many years ago when Ron Kangas sat his little butt next to his grandmother Sanna, and wove rugs during the Depression.
One of my fellow members of our Home and Community Education Group, Charlotte, (who is also my dear old neighbor from when we lived on the river) gave me two white chenille bedspreads. They're absolutely wonderful to weave into thick rugs, after they are cut into long pieces. The only problem is the chenille is fluffy and makes a bit of a mess. But we don't care. The design of this rug is strips of the white chenille and interspersed throughout the rug are laid in pieces of knit fabric we call "Caterpillars"! They are very similar in color to the book about The Very Hungry Caterpillar. A rug like this makes a great baby shower gift when accompanied by a copy of that very popular book. I plan to weave up 2 rugs, and give one to Charlotte. The other will be for sale in my Etsy shop.
The caterpillars are actually knit pieces of surplus sock fabric that a friend buys in bales from a company out in New York called Soulmate Sock Company. These are the defective socks that are sliced apart and sold as scrap. My friend Hilary at www.crazyasaloom.com sells these by the pound. I have a box full, and I cut them a little bit smaller than how they are originally shipped. I lay them in each open shed as I weave, and they create perfectly colorful caterpillars!
Here is a little YouTube that Steve shot of us while we are weaving. You can see how it's Claire's job to pick out the little caterpillars and decide which color is next, while I take care of the beating of the overslung beater on the heavy rug loom. I am so glad that all of my grandchildren enjoy helping me with weaving, spinning, quilting, or other fun projects in the She Shed. We are making memories.
I did go to an antique sock cranking meeting last week.... It is held four times a year over in Oconto Falls. I'm glad that I did go, because a gentleman arrived from Escanaba for a first-time visit to our group. I had met him last fall when we were up there camping near the Escanaba State Fair. With the help of my sister, I had purchased my Singer Featherweight Sewing Machine from him. He restores them, as well as repairs other sewing machines. He has a fascination for the antique circular sock knitting machines and has restored a couple of them as well. I had invited him to come down from Escanaba which is about an hour and a half drive away to attend one of our meetings if he happened to want to join us. And he did! He brought along a very interesting friend by the name of Joanne who is also a very accomplished spinner and knitter. We had a great time visiting and he shared some projects with us.
He knit these sleeves on the sock machine
and stretched them over Christmas Ornaments!
We were able to share some patterns, sources, insights and ideas. Plus laugh a lot and go get some lunch nearby. It's a whole day spent with our circular sockknitting machines.
He also was able to repair one of the other member's malfunctioning sock knitting machine for her. She was delighted that he could just fix it on the fly and she was off and running again in no time with her cranky machine.
Here is my sockknitting machine. It's an oldie but a goodie. I can get a pair of socks done in about an hour, with no interruptions. But of course in a room of other knitters, that isn't so easily done. But we learn a lot and share sources of good yarns or parts or patterns.
I got a couple socks cranked up as well as a good day of fellowship and being out of the house for a bit.
~~~~~~~~
So basically that is how I was spending the month of January. Working on a couple quilts, working on some rugs, doing some knitting, and enjoying the warmth of inside of the house.
As for Steve, he was fiddling around with a few things in his garage and installed some new shop lights. He now has the entire ceiling of the garage insulated which makes it much warmer out there to work on things if we need to. The winds are no longer blasting in through the eaves along the soffits vents or the ridge vent along the top of the roof line. Nice! In the spring we will take care of hanging sheetrock on the ceiling to finish it off nicely.
So he was thinking it's time to start another project.
A couple months ago we picked up 18 bundles of new beadboard strips from a guy on Facebook Marketplace. They are 8ft long and we are going to cut them in half into 4 ft pieces. There is a section along the wall of the kitchen that we would like to cover in beadboard wainscoting 4 ft high. It will tie in the beadboard pantry cabinet we restored last summer and blend it more with the rest of the beadboard type cabinetry on the other side of the kitchen. I think it will draw it all together and coordinate it nicely. The top edge cap will have a bit of trim kind of like a plate rail and a bit of egg and dart molding underneath that will mimic the trim around all of our old fashioned window and door frames in the house.
He brought in a couple pieces to lay on each side of the pantry cabinet. Of course they will be about 10 inches higher because they will start at the edge of the baseboard molding. Also they will be sealed with shellac on all of the knots to prevent bleed through and then painted the same color as the cabinets and trim in our kitchen.
Then---- in the bathroom we are going to do the beadboard all around 4 feet high as well. I love a beadboarded bathroom. We had done beadboard in a varnished and stained type in the bathroom at our last house in Chilton. It gives such a beautiful old fashioned look to the bathroom.
This bathroom, we are going to install it and it will be painted to match. I think we're going to pull off the wallpaper on that one wall because that's too busy. I think I will like the plain clean lines of the beadboard. It will be good to get something on that wall along the side of the tub. When using the handheld shower, sometimes a tiny bit of overspray does hit the wall. I would rather it hits beadboard than the wallpaper. I'm not a fan of any wallpaper, especially in the bathroom. The wallpaper is starting to pull up a little bit on the corner near the window and I think I would prefer to get rid of it.
I got up my figures and Steve got out the tape measure and we figured out how many pieces we will need. It looks like we will have more than enough! That way if there are some pieces that have cracks or splits or big ugly knots, we can kind of cut around them and set those aside.
Steve started with one piece just to cut an outline of the lip edge of the windowsill and work to the right and then to the left. That is best to start with the hardest piece first and then work in each direction. The slabs of wood fit together with tongue and groove. We will be putting a white adhesive on the wall and then nailing them into place with his trim nail gun. Once all of the boards are up, I will shellac the knots and then give them two coats of my primer paint mix to make it all come together and it will look custom made!
That's as far as he got today--- one board --- because the football playoff games came on TV. This evening he is watching the second game of the day so I'd imagine we aren't doing anything more with the beadboard today or this evening. That's why I'm taking the time to write the blog while he is watching the TV.
Once the Packers lost last week and we're out of the playoffs, I kind of lose interest in any of the other playoff games. Although I will watch the Super Bowl, I'm just sad that the Packers aren't playing.
~~~~~~~~
February is going to be cold and I don't see much of a thaw coming. I think we will stay snuggled in nice and warm, put our feet up, and look out the windows of the She Shed at the snow.
Posts
